WARM AUDIO WA-C1 Chorus Vibrato

Faithful recreation of the most famous fully analog Chorus effects pedal The WA-C1 Chorus Vibrato is a faithful reproduction of the most celebrated fully analog chorus in the history of guitar pedals, enriched with additional features to explore new possibilities of modulated, uncompromising sounds. The WA-C1 is equipped with a high-quality, fully analog preamp, much appreciated by guitarists who require an ultra-responsive response. The chorus setting features separate controls for depth and speed, overcoming the limitations of vintage units while maintaining a sound faithful to the original. The vibrato section is reproduced authentically compared to the original pedals, and an added hi-z switch on the back of the pedal allows players to compensate for the higher impedance of guitars compared to keyboards, improving the clarity of the high frequencies, if desired. The definitive original chorus stompboxThe WA-C1 faithfully recreates the most celebrated fully analog chorus and vibrato pedal, known for its pure tones and rich modulation. It combines a faithful circuit design with separate controls for depth and speed in chorus mode and an additional hi-z option for an uncompromising 100% analog chorus experience. The WA-C1 has a single input and both mono and stereo outputs.No emulation, pure analog preampThe WA-C1 is equipped with a 100% analog preamplifier, which mirrors the original, with a level control that adds bite, depth and a slight natural compression to the guitar tones. The entire pedal circuit is internally supported by a voltage regulator that provides a robust power supply even when using an external 9 V power supply. The preamp tone adds color and character even in bypass mode. Deep and classy chorusThe WA-C1 offers depth and classy detail on the mid-frequencies, associated with analog chorus pedals such as the Bucket Brigade Device. Using a modern reproduction of Xvive's MN3007 BBD chip, together with high-quality components and a boutique-level construction, the WA-C1 is carefully adjusted to replicate the depth and speed of the original pedal, returning the detail expected from the most sought after vintage pieces. Rich, three-dimensional vibrato When you want to obtain a truly vibrant sound, you can activate the Vibrato setting of the Warm Chorus Vibrato to add speed and dynamism to your tone. Experimenting with vibrato mode offers modulation tones similar to rotating ones, ideal for funk, fusion, blues, jazz, and more. The WA-C1 includes a flashing LED on the front panel to monitor the effect, indicating which setting is active and the modulation speed. Separate controls for depth and speed of the choruThe WA-C1 has independent controls for depth and speed, unlike the “intensity” control of vintage models, which increased both depth and speed simultaneously. With the WA-C1, you can overcome these limitations, setting a greater depth and a slower speed to obtain even richer chorus tones.Selectable impedance for multiple sourcesThe WA-C1 has a selectable impedance switch on the rear panel, allowing you to choose between the vintage 50k ohm input impedance and the 1.1M ohm Hi-Z setting, ideal for passive string instruments, in order to improve clarity. This switch also works in bypass mode, maintaining sound clarity.Hand tested in Austin, TXLike all Warm Audio products, the WA-C1 is meticulously tested and hand inspected by qualified technicians with a passion for music, in Austin, TX, USA.Technical specificationsChorus Pedal and Vibrato 100% Analog Stereo with Selectable Depth, Speed and Impedance Controls.Controls: High/Low Input Sensitivity, Preamp Level, Chorus Depth and Speed, Vibrate Depth and Speed, On/Off of the Effect, Chorus/Vibrato Switch, Hi-Z On/Off. Components: 5x IC (including 3x Texas Instruments premium audio operational amplifiers in the signal path), 11x discrete transistors, 3x FET, 19x diodes, 2x MOSFET and a reproduction of Xvive's MN3007 BBD chip.Power consumption: 800mW; 90mA at 9V with internal operation at vintage-correct voltage via dual DC-DC voltage converter.Input sensitivity: 80mV/10mv.Output level: 315mv.Jack: 1x Input, Output 2x.: L: 16.51 cm | H: 9.65 cm | D: 4.06 cm | Weight: 0.86 kg